Telefunken m-12 hum problem

Alles zum Thema "Fragen und Technik" bei professionellen Studio- und Tonbandgeräten der Firma Telefunken

Moderator: Administratoren

Antworten
djzero78
Jungspund
Jungspund
Beiträge: 5
Registriert: Dienstag 5. April 2016, 20:46

Telefunken m-12 hum problem

Beitrag von djzero78 »

Hello,

I am in the process of restoring a Telefunken M12 tape recorder. After turning it on, on the outputs there is a noticeable hum. I'm trying to figure out what the typical levels are for this tape recorder. Do you have that model? Could you tell me something about the output hums on your tape recorders? Or would you otherwise have any idea how to fix this problem? I would appreciate any help.

Best regards,
Benutzeravatar
cavemaen

Re: Telefunken m-12 hum problem

Beitrag von cavemaen »

Hi,

the M12 is the Sister from M28 and round 40 Years old. The better Version is M12A or M12B.

You need the Schemals and a lot of Condensers.

Regards,

Rudy
djzero78
Jungspund
Jungspund
Beiträge: 5
Registriert: Dienstag 5. April 2016, 20:46

Re: Telefunken m-12 hum problem

Beitrag von djzero78 »

Hello,

I already have the schematics and I have replaced all of the electrolytic and tantalum condensers, and there is still a persistent and significant hum on the outputs.

Regards,
Benutzeravatar
cavemaen

Re: Telefunken m-12 hum problem

Beitrag von cavemaen »

Oh, you find it with the Oszilloskop, or it's on Mechanical?
Benutzeravatar
revfan

Re: Telefunken m-12 hum problem

Beitrag von revfan »

Hallo,

I have two m12b working and there is absolutely no hum to hear.

As it is a simple looking but professional "high end" recorder used by german public radio in the old days You have some kind of a technical problem


regards

revfan
djzero78
Jungspund
Jungspund
Beiträge: 5
Registriert: Dienstag 5. April 2016, 20:46

Re: Telefunken m-12 hum problem

Beitrag von djzero78 »

Before, my M12 had a shorted tantalic condenser 4,7uf on the PSU and bias board. It caused the 0,315 fuse to turn off on the board and excessive heating of the RCA 40250 transistor. Is it possible that the SGS L 123 stabilizator system lost its parameters and started causing the hum? And does the SGS L 123 have an LM 723 equivalent that could be swapped for it?

Regards,
djzero78
Jungspund
Jungspund
Beiträge: 5
Registriert: Dienstag 5. April 2016, 20:46

Re: Telefunken m-12 hum problem

Beitrag von djzero78 »

In the attachment is the level of the hum. Inputs in the preamp on the line level are set to minimum. The hum can be heard in the speakers only with the volume set to maximum.
Du hast keine ausreichende Berechtigung, um die Dateianhänge dieses Beitrags anzusehen.
djzero78
Jungspund
Jungspund
Beiträge: 5
Registriert: Dienstag 5. April 2016, 20:46

Re: Telefunken m-12 hum problem

Beitrag von djzero78 »

The hum is evidently introduced at the level of playback head preamps. I've disconnected the head, safeguarding the inputs with a resistor to not cause excitation and it was still the same level of hum. I've noticed that getting my finger got close in the vicinity of the high frequency filters on the playback head preamps board would reduce the hum. Is it possible it's a problem with screening the potentiometers, or perhaps a factory-made fault?

Regards,
Bricksounder
Haudegen
Haudegen
Beiträge: 282
Registriert: Samstag 23. Juni 2012, 17:47
Wohnort: "ländlich" westliches Allgäu
Vergebene Danksagungen: 12
Erhaltene Danksagungen: 54

Re: Telefunken m-12 hum problem

Beitrag von Bricksounder »

so it's not really easy, to help from far away

but first I would check all parts of powersupply
is the DC-Voltage on all different Values free of hum ???

your hum is not so usual ... normaly a hum at DC Powersupply is at 100Hz
with it's peak ???

may be one of Diodes on the way from AC to DC is the problem ???

I do not know the M12 .... is there any regulator circuit with a destroyed Elko???
may be there is a loop back to the DC supply ???

???
good look

please let us know about your success

Greetings Ralf
Tonbandspulen ohne "wow & flutter"
Tonbandspulen mit gerfrästem ALU-Kern
Antworten